b'COMPOTABLESSITE FITTINGS | FOOT P |U TMRPUSDESIGN COMPOTABLESSITE FITTINGS | STIRRU |P T PRUUMDPESSIGNINFLA INFLAThe Bronze Age is Over The most versatile Y-Valve on the market. 58153.1 AquavalveThe most versatile Y-Valve on the market with the ability to mix and Leaders in marine composite fittings. match fittings, adjust the angle of piping and flip the face plate to suit the installation.Typical Manual Aquavalve The TruDesign Aquavalve is designed58153.1 Standard for the diversion and control of the flow of effluent or water. (Y valve) Installation Used in marine toilet applications theAquavalveeffluent can be channelled overboard or held in a holding tank for later discharge overboard or to a shore side facility. Models1. Standard Aquavalve2. Through Bulkhead AquavalveTHROUGHBULKHEAD VENTED LOOPS Features: CARBON FILTER Clear indication of which port is in HOLDING TANK VENTthe closed position All three ports female 1 BSP58155.1 Aquavalve Through58166.1 Extension for STRAIGHT TAIL 120 BEND Parallel threads but can connect 3/4"Bulkhead up to 15mm Through Bulkhead & 11/2" hoseAquavalve up to 22mmEasy mounting - screws directly to bulkhead or floorAquavalve Versatility with Aquavalve hose fittings316 Stainless Steel fastenings Each valve is leak pressure tested Design burst pressure rating of 300 PSI (2,070 kPa) User serviceable Lockable, prevent accidental discharge AQUAVALVE Each valve supplied with spanner. (Y VALVE) The TruDesign Aquavalve is moulded from a glass-reinforced nylon PUMP composite. High strength, high-modulus glass fibres impregnated into the nylon provides dramatic strength,CodeProductBulkhead Thread stiffness, toughness, and dimensional58153.1Aquavalve StanardN/A1 stability.58155.1Aquavalve Through Bulkhead15mm 158166.1Extension for Through Bulkhead Aquavalve22mm N/A HOLDINGTANK Aquavalve Hose FittingsA full range of hose tail fittings of different sizes and angles are available. Featuring male 1 BSP parallel TAIL - LONGthreads designed for direct installation CONNECTOR THREAD 90and sealing on the red gaskets included with the Aquavalve.TANK FITTINGHose tail sizes are available in common AND TUBE hose sizes from 1938mm. Bends TAIL - LONG THREAD 120TANK LEVEL SWITCH allow tidy routing of hoses and are supplied with a thicker seal option SKIN FITTING TAIL - LONG THREAD (Blue) which can be used in place of the Aquavalves red seals to allow fittings to be rotated to a more suitable LOAD BEARING COLLAR BALL VALVE position if needed.INLET ABYC H-27 RATED TO 500 LB OUTLET BALL VALVE SKIN FITTINGTHREADED CONNECTORLOAD BEARING COLLAR CodeProductHose SizeThread Size VENT ABYC H-27 RATED TO 500 LB58180.1Aquavalve Hose Tail White19mm 1 Y PIECE CONNECTOR 58182.1Aquavalve Hose Tail White25mm 158184.1Aquavalve Hose Tail White32mm 1 58186.1Aquavalve Hose Tail White38mm 1 58189.1Aquavalve Hose Tail White 90 25mm 1includes Blue Seal58190.1Aquavalve Hose Tail White 90 38mm 1includes Blue Sealtrudesignmarine.com Not drawn to scale. Plumbing layouts are indicative only. If in doubt, seek professional advice. 58191.1Aquavalve Hose Tail White 120 25mm 1includes Blue Seal58192.1Aquavalve Hose Tail White 120 38mm 1includes Blue Seal 62| 63'